鋁板在生產過程中往往會有很多問題，鋁板生產中為常見的問題不外乎表面問題、板型問題、軋制厚度問題。所以鋁板生產廠家在鋁板生產中要時刻的關注以上幾個要點。
There are often many problems in the production of aluminum plate. The most common problems in the production of aluminum plate are surface problems, plate shape problems and rolling thickness problems. Therefore, aluminum plate manufacturers should always pay attention to the above points in aluminum plate production.
鋁板生產中的表面問題：
Surface problems in aluminum plate production:
表面問題主要為擦劃傷、黃油斑問題，鋁板在生產過程中如果機臺上面有金屬顆粒那么會在生產過程中出現紋理一直的擦劃傷，生產人員需要立即停機清理機臺。黃油斑問題是由于軋制油沒有及時更換或者是軋制設備的吹風系統出現故障導致的，雖然后期可通過鋁板拉彎矯清洗進行處理，但是生產人員還是需要注意黃油斑，如果對于高要求的外觀件對于黃油斑都是視為不合格的鋁板。
The surface problems are mainly scratches and grease spots. If there are metal particles on the machine during the production process, the texture will be scratched all the time. The production personnel need to stop the machine immediately to clean the machine. The problem of grease spots is caused by the failure of the rolling oil or the failure of the blowing system of the rolling equipment. Although it can be treated by the cleaning of the aluminum plate in the later stage, the production personnel still need to pay attention to the yellow oil spots. If the appearance parts with high requirements are regarded as unqualified aluminum plates.

鋁板生產中的板型問題：
Plate shape problems in aluminum plate production:
板型問題一直是比較難以控制的，主要和軋機軋輥有關系，軋機如果在長期軋制過程中沒有及時修復軋輥磨損的間隙則會出現板型波浪問題，中浪和邊浪都可能會產生。波浪板型問題已經發現生產人員需要立即向生產主任反饋，排除是否因?yàn)檐垯C(jī)壓力不均勻還是其它原因，如果是軋輥磨損嚴重需要更換軋輥。
The plate shape problem has always been difficult to control, which is mainly related to the roll of the rolling mill. If the rolling mill fails to repair the worn gap of the roll in time during the long-term rolling process, the plate shape wave problem will occur, and both medium wave and side wave may occur. The wave plate shape problem has been found. The production personnel need to immediately feed back to the production director to rule out whether it is due to uneven rolling mill pressure or other reasons. If the roll is seriously worn, the roll needs to be replaced.
鋁板生產中的厚度問題：
Thickness problems in aluminum plate production:
還是和軋機有關系，軋機壓力不均勻?qū)е拢壳败垯C(jī)都有在線測量設備，該問題已經不再經常出現。
It is still related to the rolling mill, which is caused by the uneven pressure of the rolling mill. At present, the rolling mill has on-line measuring equipment, and this problem is no longer frequent.
鋁板硬度問題：
Hardness of aluminum plate:
主要和退火時間有關系，很多時候由于退火時間不足導致力學性能不達標，比如半硬狀態的鋁板出現折彎開裂，或者拉伸鋁板出現拉伸開裂均是鋁板硬度不達標，主要需要檢查退火設備的溫度、退火時間。
It is mainly related to the annealing time. In many cases, the mechanical properties are not up to the standard due to insufficient annealing time. For example, the bending cracking of semi-rigid aluminum plate or the tensile cracking of stretched aluminum plate are not up to the standard. It is mainly necessary to check the temperature and annealing time of the annealing equipment.
以上是鋁板生產中的常見問題，本公司是一家鋁板生產廠家，為用戶提供優質鋁板帶產品，關注鋁板質量，爭創鋁板。更多相關事項就來我們網站http://www.wangzhuanquan.cn咨詢了解吧！
The above are common problems in aluminum plate production. The company is an aluminum plate manufacturer, providing users with high-quality aluminum plate and strip products, paying attention to the quality of aluminum plate and striving to create an aluminum plate brand. For more information, please visit our website http://www.wangzhuanquan.cn Consult and understand!